How Can Green Building Materials Balance Carbon Reduction, Performance and Cost?
2026-10-20
Global concern about climate change and resource consumption is changing how building materials are selected. Energy efficiency, green procurement and life cycle assessment are drawing attention to emissions from both the operation of buildings and the materials used to construct them. The United Nations Environment Programme (UNEP) calls for a combination of resource efficiency, material substitution and improvements to conventional materials such as cement and steel. [1]
For building material producers, the question is increasingly practical. Can a lower carbon product meet engineering requirements and still deliver an acceptable financial return?

Why cement and concrete matter to building decarbonization
According to the Global Status Report for Buildings and Construction 2024–2025, published by UNEP and the Global Alliance for Buildings and Construction, the construction and operation of buildings accounted for approximately 37% of global CO₂ emissions in 2023. This includes emissions associated with building energy use and the production of construction materials. [2]


UNEP. Global Status Report for Buildings and Construction 2024–2025
Cement and concrete are a major part of the materials challenge. UNEP estimates that their production accounts for around 8% of global CO₂ emissions. Conventional Portland cement clinker is an important source: the kiln requires high temperature heat, while the chemical decomposition of limestone also releases CO₂. [3]

UNEP. Building Materials and the Climate: Constructing a New Future.
Concrete is widely used in housing, roads, bridges, industrial facilities and energy infrastructure. At this scale, improving binder efficiency and reducing demand for carbon intensive clinker and cement can contribute to construction decarbonization. Finding workable lower carbon materials is therefore a current production challenge as well as a long term research priority.
Lower carbon materials also need a viable business case
Continued adoption depends on whether a technology meets both engineering and operating requirements. Ready mix producers need workable concrete, slump retention during transport, suitable pumping behavior and consistent strength. PHC pile and precast producers also need adequate demoulding strength, compatible curing regimes and efficient production cycles.
Lower raw material costs may not translate into a net saving if they are accompanied by longer curing, greater quality variability or substantial equipment investment. The financial assessment should therefore include material procurement, transport, admixture dosage, equipment changes, quality control and production efficiency.
A useful solution must establish its emissions benefit, meet the required performance and remain competitive on total cost. Wider deployment also depends on whether it can be adapted when local materials, climate and production processes change.
Available approaches and their implementation requirements
1. Greater use of supplementary cementitious materials
Replacing part of the clinker or cement with fly ash, ground granulated blast furnace slag (GGBS), calcined clay or natural pozzolans is an established route to lower carbon cement and concrete. In a suitable binder system, these materials can reduce demand for clinker.
Deployment depends on supply, consistent quality and compatibility with the binder system. Availability, reactivity and price differ between regions. Higher replacement levels require checks on strength development, curing and fresh concrete performance. UNEP identifies reliable supply chains and suitable standards as important conditions for wider adoption. [3]
2. Mix design optimization
Optimizing aggregate grading, particle packing, paste volume and the water reducing admixture system can help identify unnecessary binder use while maintaining the required performance.
The available saving depends on the reference mix and local materials. A mix that has already been carefully optimized may have less scope for further cement reduction before strength, workability or production consistency becomes a constraint. Reduction targets therefore need to be established through trials rather than by applying a fixed percentage.
3. Alternative binder systems
Alkali activated materials and geopolymers offer another way to reduce reliance on conventional Portland cement. Some systems have already reached commercial use.
Wider use requires control of raw material variability, activator selection, handling, curing and compliance with applicable standards. RILEM research identifies uneven global material availability, variable material properties and the need for suitable guidelines and testing methods as barriers to broader adoption. These systems need production and validation procedures suited to the particular materials and application. [4]
4. More efficient cement production and lower carbon energy
Improving kiln efficiency, using alternative fuels and reducing the carbon intensity of energy can lower emissions from cement manufacture. Cement producers implement these measures according to plant conditions, energy supply and investment requirements.
Energy improvements need to work alongside other measures to address the process emissions released when limestone decomposes. [5]
5. Carbon capture for deeper emissions reductions
Carbon capture can address CO₂ released during cement production and is an important route to deeper emissions reductions. It also requires capital, energy and supporting infrastructure.
The International Energy Agency (IEA) estimates that early commercial plants producing near zero emissions cement with carbon capture and storage could have production costs 75–150% above conventional plants, depending on the region. This estimate applies to those specific cement production facilities and illustrates the potential financial challenge of deep decarbonization. [6]
These approaches act at different points in the value chain and can be combined. For concrete producers, the practical choice is which measures can be introduced under existing operating conditions and deliver measurable financial and environmental benefits.
The NINGINE approach to improving binder efficiency
Improving the use of supplementary cementitious materials in an existing concrete mix gives producers another route to investigate, alongside new binder systems and changes to production facilities. NINGINE CCRA® Concrete Carbon-Reducing Admixture was developed to address this opportunity.
According to NINGINE technical information, CCRA® uses chelation assisted solubilization and related mechanisms to improve the reactivity and utilization of fly ash, GGBS and other supplementary cementitious materials. The aim is to increase their contribution to the binder system, creating scope to reduce cement content in an optimized mix.
CCRA® product and application mechanism
Local materials as the starting point
Trials begin with the cement, fly ash, GGBS, aggregates, water reducing admixture and water actually used by the customer. This provides a basis for developing a mix suited to the local supply rather than assuming that one mix design will work everywhere.
Validation against the required performance
Following cement reduction, workability, early strength, 28 day strength and project specific durability requirements need to be checked. The optimized mix must meet the demands of both production and the intended engineering application.
Implementation within the existing process
Mix trials and pilot production establish the requirements for addition, dosing, mixing and quality control before full production. CCRA® can be used alongside PCE based water reducers, with compatibility and dosage verified in advance.
Financial evaluation using actual local costs
The material cost per cubic metre is compared before and after optimization using local cement, SCM and admixture prices. Any necessary production adjustments are included to determine whether the mix can deliver a sustained financial benefit.
The value of the product is assessed against a concrete production question: can the required performance be achieved with less cement and a better total production cost?
From comparative trials to consistent production
Wider adoption of lower carbon concrete requires evidence on performance, cost and emissions. Cement reduction should be supported by trial and production data, and the financial benefit should reflect local prices and operating conditions.
The carbon assessment should account for the materials in the complete mix and relevant transport impacts. A percentage reduction in cement content should not automatically be presented as the same percentage reduction in concrete emissions.
NINGINE starts with the customer’s raw materials and reference mix. Application reviews, comparative trials, pilot production and ongoing monitoring help customers evaluate CCRA® and introduce validated mixes into their production systems.

CCRA® Local trials
To assess the cement reduction and cost optimization potential of your mix, share your raw material information, reference mix and performance requirements with the NINGINE technical team. Email: obd@ningine.cn
References
[1] UNEP. Building Materials and the Climate: Constructing a New Future.
https://www.unep.org/resources/report/building-materials-and-climate-constructing-new-future?blaid=6293645
[2] UNEP and GlobalABC. Global Status Report for Buildings and Construction 2024–2025. Data cited: 2023.
https://wedocs.unep.org/handle/20.500.11822/47214
[3] UNEP. How blended cement, used everywhere from ancient Rome to modern London, could help counter climate change.
https://www.unep.org/en/news-and-stories/technical-highlight/how-blended-cement-used-everywhere-ancient-rome-modern-london
[4] Rossi et al. Future perspectives for alkali-activated materials: from existing standards to structural applications. RILEM Technical Letters 7, 159–177 (2022).
https://doi.org/10.21809/rilemtechlett.2022.160
[5] IEA. Technology Roadmap: Low-Carbon Transition in the Cement Industry (2018).
https://www.iea.org/reports/technology-roadmap-low-carbon-transition-in-the-cement-industry
[6] IEA. Breakthrough Agenda Report 2025: Cement and concrete.
https://www.iea.org/reports/breakthrough-agenda-report-2025/cement-and-concrete
Previous page: